rounds.com
Embedded Magnetic Magazine Carrier
Ammo at Your Fingertips
Designed for smaller capacity steel magazines.
Each magazine is held by a few pounds of magnetic force.
Questions, and customer service:
Email us
Typical installation takes 10-20 minutes.
Patent pending.
Ready to buy? Select your color and model.
All images below show M700X2 Magnetic Magazine Carrier in Camo color installed on Mossberg 702 Plinkster.
Click/tap on image to enlarge.
Carrying 50 rounds in 5 magazines on the right side.
Click/tap on image to enlarge.
Carrying 100 rounds in 10 magazines on the right side.
Click/tap on image to enlarge.
Carrying 150 rounds in 15 magazines. Suitable for a right-handed person.
Click/tap on image to enlarge.
Carrying 100 rounds in 10 magazines. Suitable for a right-handed or a left-handed person.
Click/tap on image to enlarge.
Same as above, but different angle.
Click/tap on image to enlarge.
Carrying 50 rounds in 5 magazines on the left side.
Click/tap on image to enlarge.
Carrying 100 rounds in 10 magazines on the left side.
Click/tap on image to enlarge.
Carrying 150 rounds in 15 magazines. Suitable for a left-handed person.
Click/tap on image to enlarge.
Magnetic force is holding heavier part of the rifle.
Click/tap on image to enlarge.
Magnetic force is holding the entire rifle with a scope and a bipod.
Click/tap on image to enlarge.
M700X2 Magnetic Magazine Carrier installed on Mossberg 702.
WARNING! This is not a toy. This product utilizes most powerful permanent magnets in the world.
- This product cannot be used if you or anyone else in close proximity has a medical device such as pacemaker.
- This product may affect electronic and navigational equipment, for example, compass at proximity of 10" or closer.
- This product will not work with magazines which are made of stainless steel, aluminum, or polymer.
Magnetic Strip Length, and Model Compatibility
Model | Left Side | Right Side | Compatible Model |
M500X2 | 5" | 5" | None |
M500R1 | None | 5" | M500L1 |
M500L1 | 5" | None | M500R1 |
Model | Left Side | Right Side | Compatible Model |
M600X2 | 6" | 6" | None |
M600R1 | None | 6" | M600L1 |
M600L1 | 6" | None | M600R1 |
Model | Left Side | Right Side | Compatible Model |
M700X2 | 7" | 7" | None |
M700R1 | None | 7" | M700L1 |
M700L1 | 7" | None | M700R1 |
How to pick the right length.
- If model number ends with '2', then you are purchasing two magnetic strips - one for each side of the stock.
Magnetic strips have to be installed symmetrically on both sides of the stock.
- If model number ends with '1', then you are purchasing a single magnetic strip.
Make sure to order the correct side (left or right).
If later on you decide to purchase magnetic strip for another side,
it has to be placed simmetrically to magnetic strip you already have.
If you mismatch the sides (e.g. both are for the right side),
magnetic forces will be pushing both magnetic strips away from each other,
resulting in incorrect installation.
- Any magnetic strip should not be closer than 1"
to the rear end of the stock (the butt).
- Grab your rifle, assume shooting position with your trigger hand,
and notice the point on your rifle's stock where the rear of your palm ends.
Magnetic strip should not be closer than 1" to this point.
- Consider your personal preferences, dimensions and shape of your magazines,
and whether you will be using flat and/or upright magazine placement.
These factors may pose additional limitations.
Warning for Do-it-yourself enthusiasts.
- Very few people have the patience, the tools, and the know-how to handle world's most powerful magnets.
- Individual magnets purchased elsewhere come bunched up together, and are attracted to each other with a force exceeding 20 lbs.
It is virtually impossible to separate them, and quite challenging to assemble them in a single strip.
- One wrong move may cause magnets to attract violently, likely breaking them, and very likely pinching your fingers with the force of 20 lbs.
- We pre-assemble magnetic strips, and deliver them to you along with a carefully developed installation process,
which assures ease of installation and your safety.
Return Policy.
- You have to request RMA via
Email.
- Buyer pays for return shipping.
- Shipping & handling fees are not refundable.
- An item which has not been installed, and is not damaged in any way, will be fully refunded.
- If any amount of wrapping tape was used, do not return it as we are unable to re-use it. Your refund will be reduced by $5.
- For every broken/missing magnet, your refund will be reduced by $5.
Firearm Manufacturers, and Aftermarket Manufacturers.
- If you want to incorporate On-firearm Magnetic Magazine Carrier into your product line we encourage your to reach out to us via
Email in order to negotiate a Licensing Agreement.
- Manufacturing, incorporating, and/or distributing this or similar product without a license puts you at risk of a lawsuit once
our patent is granted.
- A long term licensing strategy will put you ahead of others, and may significatly benefit your company in the long run.
Law Enforcement Officers, and members of the US Military.
- On-firearm Magnetic Magazine Carrier is a new product which, as far as we know, has never been used by Law Enforcement or the Military.
- We know that out there in the field, being quicker by a second or having an extra round could make all the difference.
- That is why we would especially appreciate your feedback.
If you have any thoughts on how to utilize this product in what you do, or how to make it better,
please
Email us.
Back to top
Ready to buy